Converter three-phase meter MID - Transformer kilowatt-hour meter 5A DSZ15WD-3x5A MID

DSZ15WD-3x5A MID 28305015 4010312501641 EAN/GTIN DE 30298319 WEEE

Our best price
13,263.18₹ excl. VAT
19,132.20₹ (-30.68% RRP***)

5-6 days* (IND)

Safety and hazard information
Please note that electrotechnical work may only be carried out by qualified electricians or under their guidance and supervision. Observe any deviating country-specific electrical installation standards and regulations and seek advice from a local electrician.In addition, observe more current safety instructions and regulations for the products on the manufacturer's side or the product descriptions and installation instructions on the manufacturer's side.

Devices with a connected load of > 380V/400V require a heavy current connection and may only be connected by an approved electrical company. Devices with a power rating > 12kW require the approval of your grid operator (Germany, other countries may differ).
read more
show less
Converter three-phase meter MID DSZ15WD-3x5A MID meter type electronic, rated current (In) 5A,... more
Converter three-phase meter MID - Transformer kilowatt-hour meter 5A DSZ15WD-3x5A MID – Eltako – 28305015 – 4010312501641: Converter three-phase meter MID DSZ15WD-3x5A MID meter type electronic, rated current (In) 5A, maximum current (Imax) 6A, rated voltage (Un) NL 230 ... 230V, rated voltage (Un) LL 400 ... 400V, frequency 50 ... 50Hz, accuracy class B, Polart four-wire, measuring transducer version, active power energy type, suitable for purchase, one-tariff tariff version, backstop, calibrated, Measuring Instruments Directive approval, optical pulse output, pulse type S0, pulse rate 10 ... 10Imp/kWh (kvarh), digital display type , Type of installation REG, width in pitch units 4, design of the other interface, number of digits 7, degree of protection (IP) IP20, only calibrated meters are permitted for electricity billing in accordance with Section 25 of the German calibration law. Non-observance is an administrative offense according to paragraph 19. Converter three-phase current meter with adjustable converter ratio and MID. Maximum current 3x5A, standby loss only 0.5 watts per path. Modular installation device for mounting on mounting rail DIN-EN 60715 TH35. 4 pitch units = 70mm wide, 58mm deep. Accuracy class B (1%). With S0 interface. This three-phase meter measures the active energy based on the currents flowing through the converters. The self-consumption of only a maximum of 0.5 watts active power per path is not measured and not displayed. 1, 2 or 3 converters with secondary currents up to 5A can be connected. The starting current is 10mA. The N connection must be present. The 7-segment LC display can be read twice within two weeks even without a power supply. The power consumption is shown on the display with a bar that flashes 10 times per kWh. To the right of the display are the MODE and SELECT buttons, which are used to scroll through the menu in accordance with the operating instructions. First, the backlight turns on. Then the total active energy, the active energy of the resettable memory and the instantaneous values of power, voltage and current for each phase conductor can be displayed. In addition, the converter ratio can be set. It is factory set to 5:5 and locked with a jumper over the terminals marked JUMPER. The converter ratio is adjusted to the installed converter by removing the jumper and resetting it according to the operating instructions. Then it is locked again with the bridge. The adjustable converter ratios are 5:5, 50:5, 100:5, 150:5, 200:5, 250:5, 300:5, 400:5, 500:5, 600:5, 750:5, 1000: 5, 1250:5 and 1500:5. Error message (false): If the outer conductor is missing or the current direction is wrong, ?false? and the corresponding external conductor are shown on the display. Danger! Disconnect the meter's voltage paths before working on the current transformers.
... more
Counter type electronic
Rated current (in) 5 A
Maximum current (Imax) 6A
Rated voltage (Un) NL 230V
Rated voltage (Un) LL 400V
Frequency 50 Hz
Accuracy class B
Polart Four conductors
Execution Transducers
Of energy Active power
Suitable for Reference
Rate design Single tariff
Backstop yes
Calibrated yes
Admission Measuring Instruments Directive
Pulse output optical
Pulse type S0
Pulse rate 0,1553
Display digital
Mounting REG
Width in division units 4
Width 70 mm
Depth 58 mm
Height 82 mm
Execution of the interface other
Number of digits 7
IP protection) IP20

Rate item

(0 reviews)
Read, write and discuss reviews... more
Customer review for "Converter three-phase meter MID - Transformer kilowatt-hour meter 5A DSZ15WD-3x5A MID"
Write a review
Evaluations will be activated after verification.
Please enter these characters in the following text field.

The fields marked with * are required.