Analog input

Analog inputs are needed to capture analog DC sensor signals / measuring values of the type (voltage signals or current signals) 0-1 V, 0-5 V, 0-10 V, 1-10 V, 0-20 mA , 4-20 mA and to send them on the bus, e.g. for wind, rain, brightness, temperature, twilight, or moisture in order to process them further. Depending on the manufacturer also standard sensors PT100, PT1000 or NTC can be used. Thus, in the KNX system, telegrams 1 byte (EIS6) or 2-byte (EIS5) can be sent for display in KNX visualizations, KNX panels or displays. Analog inputs are also able to send limit values parameterized with the ETS as 1 bit values to the KNX bus to trigger other functions or messages as soon as a measured value exceeds a defined value or falls below it. KNX analog inputs usually require a voltages supply. This eibabo catalog contains analog inputs for various automation systems (LCN, Radio Bus, KNX, etc.). KNX analog inputs can be ordered for all installation types on the surface, concealed, built into ducts, walls or ceilings or for installation in electrical distributions. Now the question arises why an analog input is required if any common weather station already offers the usual sensors and this usually with considerably more parameters. However, usually a standard KNX weather station has just a few permanently installed sensors which is usually sufficient for the purpose of measuring physical environmental variables outside. However, on the market there are thousands of different conventional active and passive sensors for different requirements and functions. Conventional active 0-1 V, 0-5 V, 0-10 V, 1-10 V, 0-20 mA, 4-20 mA current or voltage sensors might be needed specifically, for example, for special sensors to carry out regulating processes by means of KNX. The potential for these conventional sensors is enormous and can be exploited by using KNX analog inputs. KNX also provides suitable input modules for passive sensors for evaluation in the KNX bus system. The disadvantage of analog signals is the susceptibility to trouble if there are very precise requirements. Therefore, in the automation sector analog sensors are increasingly replaced by digital systems in control technology. Therefore, the demand for sensors with digital output signal is increasing. Sensor manufacturers worldwide will benefit in the coming decades from the extreme demand for a variety of sensors, for example, for contactless capture of body temperature and heart rate, the detection of specific facial expressions and gestures to the point of recognizing emotional states from various signal evaluations, for intelligent systems (automation, smart home, robotics, etc.). We are fully convinced of this.

Catalogue content:


In this eibabo® catalogue Installation bus systems > Analogue input for bus system you will find items from the following product groups:

Item overview:

  • Air conditioning technology
  • Analog actuator
  • Analog input
  • Analog input module
  • Analog inputs
  • Analog interface
  • Analog sensor interface
  • Analogue input
  • Analogue input for bus system
  • Bus system
  • Bus system analog input
  • Consumption meter
  • Control unit
  • Current output
  • EIB
  • Engine control unit
  • Fan technology
  • Fuel consumption meter
  • Heating technology
  • Input
  • Input module
  • Moellerfunk
  • Radio system
  • Sensor
  • Switching actuator
  • Switching input
  • Transducer
  • Voltage output


from the following manufacturers:

Manufacturer overview catalogue Analog input:

  • ABB
  • Busch Jaeger
  • Eaton
  • Hager
  • Issendorff
  • Jung
  • MDT
  • Merten
  • Metz
  • Schneider Electric
  • Warema


 
Analog inputs are needed to capture analog DC sensor signals / measuring values of the type (voltage signals or current signals) 0-1 V, 0-5 V, 0-10 V, 1-10 V, 0-20 mA , 4-20 mA and to send them on... read more »
Close window
Analog input
Analog inputs are needed to capture analog DC sensor signals / measuring values of the type (voltage signals or current signals) 0-1 V, 0-5 V, 0-10 V, 1-10 V, 0-20 mA , 4-20 mA and to send them on the bus, e.g. for wind, rain, brightness, temperature, twilight, or moisture in order to process them further. Depending on the manufacturer also standard sensors PT100, PT1000 or NTC can be used. Thus, in the KNX system, telegrams 1 byte (EIS6) or 2-byte (EIS5) can be sent for display in KNX visualizations, KNX panels or displays. Analog inputs are also able to send limit values parameterized with the ETS as 1 bit values to the KNX bus to trigger other functions or messages as soon as a measured value exceeds a defined value or falls below it. KNX analog inputs usually require a voltages supply. This eibabo catalog contains analog inputs for various automation systems (LCN, Radio Bus, KNX, etc.). KNX analog inputs can be ordered for all installation types on the surface, concealed, built into ducts, walls or ceilings or for installation in electrical distributions. Now the question arises why an analog input is required if any common weather station already offers the usual sensors and this usually with considerably more parameters. However, usually a standard KNX weather station has just a few permanently installed sensors which is usually sufficient for the purpose of measuring physical environmental variables outside. However, on the market there are thousands of different conventional active and passive sensors for different requirements and functions. Conventional active 0-1 V, 0-5 V, 0-10 V, 1-10 V, 0-20 mA, 4-20 mA current or voltage sensors might be needed specifically, for example, for special sensors to carry out regulating processes by means of KNX. The potential for these conventional sensors is enormous and can be exploited by using KNX analog inputs. KNX also provides suitable input modules for passive sensors for evaluation in the KNX bus system. The disadvantage of analog signals is the susceptibility to trouble if there are very precise requirements. Therefore, in the automation sector analog sensors are increasingly replaced by digital systems in control technology. Therefore, the demand for sensors with digital output signal is increasing. Sensor manufacturers worldwide will benefit in the coming decades from the extreme demand for a variety of sensors, for example, for contactless capture of body temperature and heart rate, the detection of specific facial expressions and gestures to the point of recognizing emotional states from various signal evaluations, for intelligent systems (automation, smart home, robotics, etc.). We are fully convinced of this.

Catalogue content:


In this eibabo® catalogue Installation bus systems > Analogue input for bus system you will find items from the following product groups:

Item overview:

  • Air conditioning technology
  • Analog actuator
  • Analog input
  • Analog input module
  • Analog inputs
  • Analog interface
  • Analog sensor interface
  • Analogue input
  • Analogue input for bus system
  • Bus system
  • Bus system analog input
  • Consumption meter
  • Control unit
  • Current output
  • EIB
  • Engine control unit
  • Fan technology
  • Fuel consumption meter
  • Heating technology
  • Input
  • Input module
  • Moellerfunk
  • Radio system
  • Sensor
  • Switching actuator
  • Switching input
  • Transducer
  • Voltage output


from the following manufacturers:

Manufacturer overview catalogue Analog input:

  • ABB
  • Busch Jaeger
  • Eaton
  • Hager
  • Issendorff
  • Jung
  • MDT
  • Merten
  • Metz
  • Schneider Electric
  • Warema
Close filters
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
from to

1 From 2
No results were found for the filter!
RECOMMENDED
3D
ABB - AE/S4.1.1.3 - KNX analogue input 4-ch AE/S4.1.1.3
13,314.51₹ excl. VAT

*

plus shipping
(27,323.85₹ RRP***)
KNX analogue input 4-ch
ABB
| AE/S4.1.1.3
RECOMMENDED
3D
Jung - 2225 WS U - KNX weather station Universal 2225 WS U
71,252.34₹ excl. VAT

*

plus shipping
(91,383.73₹ RRP***)
KNX weather station Universal
Jung
| 2225 WS U
RECOMMENDED
3D
RECOMMENDED
3D
Eaton - CTEU-02/01 - Radio temperature input 2-fold CTEU-02/01
8,938.94₹ excl. VAT

*

plus shipping
(14,272.25₹ RRP***)
Radio temperature input 2-fold
Eaton
| CTEU-02/01
RECOMMENDED
3D
Hager - TYF784 - KNX analogue input 4-ch TYF784
18,680.69₹ excl. VAT

*

plus shipping
(34,657.16₹ RRP***)
KNX analogue input 4-ch
Hager
| TYF784
RECOMMENDED
3D
Jung - 2214 REG A - KNX analog input 4-fold housing - KNX analogue input 4-ch 2214 REG A
16,318.26₹ excl. VAT

*

plus shipping
(26,209.30₹ RRP***)
KNX analog input 4-fold housing - KNX analogue input 4-ch
Jung
| 2214 REG A
RECOMMENDED
3D
Eaton - CAEE-02/01 - Analog input - Analogue input for bus system 2-ch CAEE-02/01
9,173.68₹ excl. VAT

*

plus shipping
(14,647.84₹ RRP***)
Analog input - Analogue input for bus system 2-ch
Eaton
| CAEE-02/01
RECOMMENDED
3D
Busch Jaeger - 6190/51-101 - Analog input 4F - KNX analogue input 4-ch 6190/51-101
14,820.61₹ excl. VAT

*

plus shipping
(27,323.85₹ RRP***)
Analog input 4F - KNX analogue input 4-ch
Busch Jaeger
| 6190/51-101
RECOMMENDED
3D
Jung - 2214 REG AM - Analog input module 4-fa housing - KNX analogue input 4-ch 2214 REG AM
13,611.22₹ excl. VAT

*

plus shipping
(21,860.96₹ RRP***)
Analog input module 4-fa housing - KNX analogue input 4-ch
Jung
| 2214 REG AM
RECOMMENDED
3D
Busch Jaeger - 6190/50 - Analog input surface mounting - KNX analogue input 2-ch 6190/50
10,084.47₹ excl. VAT

*

plus shipping
(18,591.49₹ RRP***)
Analog input surface mounting - KNX analogue input 2-ch
Busch Jaeger
| 6190/50
RECOMMENDED
3D
Metz - 110 562 - T/M converter 4-channel - Direct/transformer for bus system 110 562
10,274.14₹ excl. VAT

*

plus shipping
(14,511.69₹ RRP***)
T/M converter 4-channel - Direct/transformer for bus system
Metz
| 110 562
RECOMMENDED
3D
Schneider Electric - MTN682191 - Analog input REG-K/4-fold - KNX Analogue input for bus system 4-ch MTN682191
14,758.64₹ excl. VAT

*

plus shipping
(19,530.45₹ RRP***)
Analog input REG-K/4-fold - KNX Analogue input for bus system 4-ch
Schneider Electric
| MTN682191
1 From 2
Viewed from you