Final assembly set for decentralized ventilation - Central air supply and -exhaust device PP 45 K

Final assembly set for decentralized ventilation - Central air supply and -exhaust device PP 45 K – Maico – 0095.0241 – 4012799952411: Final assembly set for decentralized Ventilation PP 45 K, energy efficiency class=A+, energy efficiency class spectrum=A+ to G, type of ventilation=decentralized supply and exhaust air, heat recovery via=other, heat source=outside air, nominal output=1.7 W, degree of heat availability=84%, with hot water preparation =no, with heating=no, with remote control=no, air connection diameter=160 mm, height=246 mm, width=246 mm, depth=282 mm, weight=3.14 kg, volume flow=42 m³/h, with water air heater= no, with additional heating=no, final assembly sets for the PushPull 45 single-room ventilation device with fan, ceramic heat exchanger, inner cover and two integrated filters (G2 + G3), so that the air is filtered in both directions. Versions: PP 45 K - with electric flap. PP 45 O - with manual flap. PP 45 RC - with radio control and electric flap. In order to achieve efficient ventilation, we recommend operating the devices in pairs. It is a basic requirement for the final assembly set PP 45 RC. Required accessories: shell sleeve PP 45 RHK or PP 45 RHL, outer cover PP 45 AK, PP 45 AE or PP 45 AW for external wall installation or reveal element PP 45 LE for reveal duct installation, room air control RLS 45 K or RLS 45 O for the final assembly sets PP 45 K and PP 45 O and radio switch DS 45 RC for the radio device PP 45 RC, Several devices (max. 6) can be controlled simultaneously via an RLS 45 K or RLS 45 O room air control. When using the DS 45 RC wireless switch, the number of devices is not limited, provided the devices are within range of the wireless switch. Optional accessories: wall block PP 45 MB, power unit PP 45 LT, EnOcean extension module PP 45 EO, EnOcean actuator PP 45 ACT, humidity sensor PP 45 HYI and PP 45 HY, CO2 sensor PP 45 CO2, VOC sensor PP 45 VOC, Air filter, replacement PP 45 G2, PP 45 G3 and PP 45 G2P, The device versions PP 45 K and PP 45 RC have an electric flap. If the devices are switched off (level 0), the flap closes automatically. The device does not consume any electrical energy. With the PP 45 O final assembly set, the outer flap is closed manually. The room air controls RLS 45 K and RLS 45 O can be expanded with the internal humidity sensor PP 45 HYI or with the external sensors PP45 HY, PP 45 CO2 and PP 45 VOC. The devices achieve energy efficiency class A+. The PP 45 RC final assembly set can be expanded with a PP45 HYI humidity sensor. The sensor is only installed in the master device. The room air controls RLS 45 K and RLS 45 O as well as the wireless devices PP 45 RC with the wireless switch DS 45 RC can be operated in 5 ventilation levels 15/20/30/36/42 m3/h and 3 operating programs permanent ventilation with heat recovery, cross ventilation and sensor-guided auto mode . In auto mode, the delivery volume is infinitely adjusted to the sensor value. With the RLS 45 O room air control, automatic operation is only possible with the connected sensor. The RLS 45 K room air control and the DS 45 RC radio switch can perform other functions such as boost ventilation (time-limited intensive ventilation) and sleep function (time-limited shutdown). With the help of the RLS 45 K room air control, communication between exhaust air devices (e.g. ECA/ER) and PushPull devices is possible. This means that when an exhaust air fan starts up, the PushPull devices switch to supply air mode in order to compensate for the resulting negative pressure. The supply air mode is possible with an after-run of 0.6 or 15 minutes. The number of devices connected is also taken into account. In combination with the EnOcean extension module PP 45 EO, the room air control RLS 45 K offers the unique possibility of connecting the wired PP 45 K and PP 45 O and the radio devices PP 45 RC with each other. With this control combination, for example, wired devices can be installed on the ground floor and wireless devices on the first floor. The entire system is controlled with the push of a button. In addition, the RLS 45 K room air control offers the option of carrying out the device configuration conveniently with the PC/laptop (Windows) using the commissioning software. Heat exchanger: With the high-performance heat exchanger and the highly efficient EC fan, the devices achieve a heat recovery rate of 84.3% at the reference volume flow according to EN 13141-8. Installation instructions: Installation takes place in 2 steps: Installation of the shell sleeve PP 45 RHK (DN 160) or RHL (DN 160) and an outer cover in a core hole DN 160 with an inclination of 1-2%. We recommend performing the core drilling with DN 182 and aligning the inclination of the sleeve using the polystyrene wedges provided. The shell sleeve is protected from contamination with plaster protection covers. This is followed by the integration of the final assembly set. No pipe laying necessary and no adjustment of the system necessary. Electrical connection: The device is delivered fully assembled and ready for use. Electrical connection is made using a plug connection. Connection to room air control RLS 45 K or RLS 45 O via plug-in control lines. The 12 VDC power line from the RLS 45 K / RLS 45 O room air control to the device is also the control line. Condensate drain: The condensate is drained off via an integrated condensate drip edge in the outer cover. Article: PP 45 K, delivery volume: 15 m3/h / 20 m3/h / 30 m3/h / 36 m3/h / 42 m3/h, energy efficiency class: A+, rated voltage: 12 V DC, SPI value according to DIN EN 13141-8: 0.11 Wh/m3, maximum power consumption: 1.2 W / 1.7 W / 2.1 W / 2.8 W / 3, 5 W, degree of protection: IP 00, DIBT approval: yes, installation position: horizontal, system type: decentralized, housing material: plastic, heat exchanger material: ceramic, colour: traffic white, similar to RAL 9016, weight: 3.14 kg, filter type: external - and exhaust air filter, filter class: G2 / G3, connection diameter: 160 mm, width: 246 mm, height: 246 mm, depth: 282 mm, required wall opening: 162 to 182 mm, wall thickness: 265 mm (if the insert is flush with the wall sleeve ) / 500 mm, degree of heat recovery at the reference volume flow according to DIN EN 13141-8: 84.3%, necessary room air control: RLS 45 K / RLS 45 O, sound pressure level: 21 dB(A) / 25 dB(A) / 31 d B(A) / 35 dB(A) / 38 dB(A) / distance 1 m, free field conditions, weighted max. element standard sound level difference Dn,w: 51 dB, approval number: Z-51.3-416, type of ventilation: decentralized Zu - and exhaust air, heat recovery via: other, degree of heat availability: 84.3%